Reinitialize your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to restore your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the settings or are click here experiencing unexpected behavior. Fortunately, resetting your Holosun is a simple process that can be achieved in just a few actions.

• First ensuring your red dot sight is powered on.
• Locate the small reset button on the rear of the sight.
• Employ a thin tool to depress the reset switch for approximately 7 seconds.
• Let go the switch and your Holosun EPS Carry Red Dot sight will restart.
• Your red dot sight should now be reverted to its factory settings.

Reset Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it to its factory configuration is a breeze. First, locate the tiny button on the bottom of your optic. Then, keep pressed it for around twelve seconds until you see the red dot blink. Your Holosun EPS Carry is now reverted to its factory settings, ready for accurate shooting.

revive your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent accidental activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

• Hold down the power button for approximately 5 seconds.
• The display will flash, indicating that the reset is successfuly initiated.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and confirm your sight's functionality. If you encounter any further problems, don't hesitate to contactHolosun's customer support.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

• Beginning with, Activate your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• While continue holding these buttons, tap the power button once.
• The display will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Original reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Reset your Holosun EPS Carry through a Factory Original Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the answer. This will set back your sight to its initial settings, clearing any altered configurations you've made. To execute this reset, follow these simple steps:

• Initially, find the reset switch on your EPS Carry.
• Then, press a fine object, like a pen tip, to depress the reset lever.
• During hold the reset lever engaged, turn your EPS Carry.
• The sight will blink a message confirming that the reset is complete.

After the reset is finished, your EPS Carry will be back to its factory settings.

Report this wiki page